Quantcast Search Results - AmayaUsers Discussion Boards

news

discussion boards mailing list tips / tricks / forms designs suppliers find a shop marketplace
News
  archives

Discussion
  main menu

Suppliers
  apparel
 
hats
 
thread
  backing
  hoops / hooping
  stock designs

Tips & Tricks
  main menu

Mailing List
  sign up now
 
my account

Amaya Shops
  locate a shop

Marketplace
  shop for supplies

Resources
  official Melco site
  online resources

 

Help Support This Site:


 


 

Search:

Type: Posts; User: Judy; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    235

    I have had one machine for 14 years that never...

    I have had one machine for 14 years that never did it. I got an almost new second machine that did it immediately. It stopped doing them when I changed out the knife. Weird, but true!
  2. Replies
    2
    Views
    777

    I invested the small fortune for the wooden one...

    I invested the small fortune for the wooden one and the arms...and I found there is only about an extra inch sewing room from the 16.8 square hoop, regardless of the size of the hoop itself. I sold...
  3. Replies
    2
    Views
    774

    Hi there, and welcome. The knife could be...

    Hi there, and welcome.

    The knife could be dull.

    The stabilization could be loose.

    The thread trim in Amaya OS could be set to short instead of medium or long.

    The thread could be too...
  4. Thread: Laser Calibration

    by Judy
    Replies
    3
    Views
    933

    I second what John says, and I go one further --...

    I second what John says, and I go one further -- I go to needle down to check centering.
  5. Replies
    2
    Views
    2,385

    I use the needle through the needle eye trick. ...

    I use the needle through the needle eye trick.

    Get a hand sewing needle -- the thinnest you can find. Stick the eye of that needle into a pencil eraser.

    When setting needles, put the tip of...
  6. If the private message is not appearing at your...

    If the private message is not appearing at your inbox, please contact me at onleejudy@aol.com. Thank you.
  7. Sent you a private message.

    Sent you a private message.
  8. Replies
    2
    Views
    2,387

    For hats at least a 12 sharp (not a ball point).

    For hats at least a 12 sharp (not a ball point).
  9. Replies
    0
    Views
    1,028

    ISO Hoop Master 12cm Freestyle Arm

    If you only use your 4" (12cm) fixture on a shirt board, I'd like to buy your freestyle arm from you. Thanks!
  10. Replies
    7
    Views
    3,792

    When I use Mighty Hoops, I always have to use a...

    When I use Mighty Hoops, I always have to use a jig, or something to hold the bottom hoop in place, The magnets draw themselves together, even when you are not ready for them to. Also, I have to...
  11. Replies
    0
    Views
    1,385

    FOR SALE - Amaya cap gauge

    I don't do enough hats that I will ever do them on two machines at once. One spare cap gauge. $125 plus actual shipping.
  12. Replies
    5
    Views
    3,449

    When weird things happen I always start at...

    When weird things happen I always start at bobbin, and tension in the hoop.

    A different bobbin or bobbin case may help;
    Adding a layer of backing (even water soluble, but most likely a tear away)...
  13. Replies
    5
    Views
    3,449

    A water soluable topping to hold it down while...

    A water soluable topping to hold it down while you embroider on it works wonders.
  14. Replies
    0
    Views
    4,237

    Wholesaler for Coats Sylko thread?

    Does anyone know who this might be?
  15. For Sale 7 in 1 fast frames, and Dog collar/karate belt fast frame

    These fit an XT. They have never been used.

    $320 each individually; take both for $600 (which includes shipping).
  16. WANTED: Hoopmaster fixture for 12 cm (4 inch) hoop

    I am getting to where I do a lot of the smaller designs on smaller clothing. If you have one that is routered out for cap backs, all the better.
  17. Replies
    2
    Views
    2,560

    Call Lonnie. I don't believe version ten...

    Call Lonnie. I don't believe version ten requires dongles...
  18. Replies
    2
    Views
    3,053

    As long as you don't use water or anything wet,...

    As long as you don't use water or anything wet, the solvy won't dissolve and stick.

    OR

    You can test on a scrap of similar fabric. There is a lot of washable velvet out there. It may not be an...
  19. Thread: Cutter

    by Judy
    Replies
    1
    Views
    2,793

    Cutter

    This is kind of a strange question --

    I have a cutter blade that keeps popping off the the push rod.

    I am waiting to be scheduled for a preventive maintenance for awhile now... so long I have...
  20. Replies
    15
    Views
    11,635

    I use the same CCF's with my XT as I did with my...

    I use the same CCF's with my XT as I did with my Big Red. I say this because I have an extra cap gauge that works with the older drivers. If you'd like to purchase it, please let me know.
  21. Replies
    15
    Views
    11,635

    You can email me at onleejudy@aol.com. Thanks.

    You can email me at onleejudy@aol.com. Thanks.
  22. Replies
    15
    Views
    11,635

    Jean -- if you don't hear back from Lucky Guy, I...

    Jean -- if you don't hear back from Lucky Guy, I am interested in your HoopTech gauge and frames, and the Organ needles. Lucky Guy first though.
  23. Replies
    15
    Views
    11,635

    Question for Lucky Guy: Can a new cap driver...

    Question for Lucky Guy: Can a new cap driver (the red one) be used with an original Melco Amaya Big Red? I thought drivers were geared to the machines they were made for. Then again...my only up...
  24. Replies
    9
    Views
    4,554

    The default setting for my machine on material...

    The default setting for my machine on material thickness is 3.

    Have you cleaned the bobbin case, and/or have you swapped out bobbin cases?
  25. Replies
    9
    Views
    4,554

    A few other things to check -- what is your...

    A few other things to check -- what is your thread feed set at in OS? Is your presser foot all of the way down and then two clicks up?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
  a Levelbest Network Site - 2013

This site is not owned by or affiliated with Melco or any companies or subsidiaries.